Chasing & Repouse' Hawaiian Plumeria Flower Bracelets Part 2

This is a view from the front side of my work. Here you can see that the leaves are domed and taking on a very nice raised shape.  You can also see the chasing that was done at the beginning when my pattern was outlined.  I will work bothon the front and back side of my work annealing in between until I get the desired relief.

Back side

Front side
Now I feel it is ready for some texture around the background of my pattern. This will help to make the flowers and leaves stand out.

These are my matting tools and use the to hammer  to pattern into the background of the flowers

You can see that the piece has texture around the flowers and leaves

Now I will clean the metal with a brass brush under running water

After Cleaning

Close up

Notice how the matted patteren make the leaves and petals stand out

Next is deterning where I want to cut out the unwanted silver

Using a caliper I decised the thickness of the brcelet and score the metal so I have a line to follow with my jewelers saw.

Notice the lines that the caliper made into my silver

Start sawing around the flowers making sure to leave the area where the band is  alone.

Once I get the flowers done I will start to saw along the marks made with my caliper for the band

Here is my first one!

Using a small needle file. I smooth out and clean up all of the edges

Make sure to go around every point and smooth out your edges

Here they both are

Close up one end

Close up other end

More to come

Chasing & Repouse' Hawaiian Plumeria Flower Part 1

Flat Chasing tools

Curved Chasing tools

Tools that I will be using to work on my piece

Hammers that I will be using from top to bottom
Rawhide mallet, Nylon weighted hammer, the other two are chasing hammers

Jewelers saw's for cutting out my sheet Sterling.

German Red pitch in a bowl with spatula
Pattern drawn and cut out of the sterling and placed in a heated bowl of pitch

this is how to start the chasing

Make sure to use a thin coating of vaseline on the metal before putting it in the pitch!

Starting with the chasing tools, start to follow the outline. 

Outlining

Continueing the outline

The flowers have been outlined. Now to remove it.

Using a heat gun, heat the pitch enough to push the pitch that was formed over the edges of the silver to melt.

Melt the pitch just enough to be able to move it off the edges without getting it to hat.

Work one area at a time.

Using a pliers lift the metal out of the pitch.

Notice how clean the back of my piece is.

Wipe off the vaseline

Notice my piece is no longer flat.

using my raw hide hammer, carefully flatten your piece around the edges as to not destroy all of the outline that you just did.

it should be pretty flat

now you can see the impression that the outline made from the back side.

this piece will be  two 6" bracelets

now reheat the pitch

and DON'T forget to add the veseline to the front, sides and a very little on the bottom edge.

lay it in the heated pitch and gently push the pitch over the bottom edge of your piece. 

make sure the pitch is not pushed to far over the edge to impede on your pattern

My Repousse tools

using these tools, I will start to force the metal out into the shape that I desire.

Here I am working the edges that I want to look curved out on the petal.

Safety Glasses are a must!!! As you can see fro this picture, Pieces of the pitch will go flying out of your bowl.
Protect your eyes!

here I am working some of the leaf

close up on one end

here is the other end

once again the piece is starting to curve from hammering it

on this side the metal is not moving much so its time to remove it

here you can see how distorted the metal becomes when it has been hammered

flatten it out the best you can without hammering on the parts that are repoussed

here I am using a wood dapping tool to help get around some of my work to flatten my piece out more.

In between each time you work from the top side to the back side, you will need to anneal your piece so you don't overwork the metal and casue it to crack.

Anneal it on both ends

More to come!